Tag Archives: Problems

Never Worry About Plumbing Problems Again With These Tips (2)

April 17, 2025   Matt

Never Worry About Plumbing Problems Again With These Tips

This is going to be one of the best resources available for you to learn more about plumbing. There might be a lot of resources available both on and offline, however we have gathered the best information in this article and sorted out the obvious or incorrect advice that you may find elsewhere.

Watch how your toilets are flushing. If you have to jiggle the handle or if it takes too long, you might have to repair some toilet parts. Replacing these parts early may help you to save on your water bills and will save you from more expensive repairs at a later date.

Before you can fix a toilet that does not flush properly, it is important that you find out what is causing the problem. Depending on what the problem is, you may be able to fix it yourself. However, more complicated toilet flushing problems may require the services of a plumber.

Plunging is not the only way to unclog a troublesome toilet. If the water in the basin is sitting low and you know there’s a clog, try dropping hot water directly into the basin with a little bit of elevation, to apply enough force to help move along the clog.

Find a plumber that you can trust. Make sure to get referrals from friends and family so that you can prevent getting ripped off, which happens often. Also make sure not to pay the plumber before the work is completed. If you do that, there will not be an incentive to get the job completed in a timely manner.

Act quickly if your pipes freeze! Shut off the water and open the faucet, enabling it to drain when it thaws. Starting with the faucet, and working your way to the iced-up area, aim a propane torch or hairdryer at the pipe – this will quickly defrost it. You could also wrap the pipe in a heating pad or aim a heat lamp at it, but this will take quite some time. A last resort is to wrap the pipe in rags and pour boiling water over it.

Tub drains can get clogged by hair and debris easily, but may be hard to access. Make use of an afghan hook to reach in and snag clogging materials. These hooks are available at most craft stores. Use slow, measured movements to avoid breaking the hair as you are pulling it out.

If you are considering a plumbing project due to having what appears to be pink or red water have your water tested first. This coloration is likely due to having rust in your water, which an average plumbing project is unlikely to fix. The rust is likely coming from your well and installing a water softener there is the best remedy to the problem.

In conclusion, it is important that you know how to take care of plumbing, but it is more important that you get your data from a reliable source. Use the great advice provided here and you will be more than happy that you took the time to do so.

Read More

Plumb Easy: Learn How To Solve Your Plumbing Problems (2)

February 24, 2025   Matt

Plumb Easy: Learn How To Solve Your Plumbing Problems

Plumbing could be a topic that is complicated. This article is filled with great do-it-yourself plumbing advice that, if followed properly, will save you from lots of aggravation.

Do not ignore a slow flushing toilet. This is usually a sign that something is wrong. It can also cause backups and overflows. The most common causes of a slow flushing toilet are sediment build up, tank malfunctions, or partial clogs. You should periodically check for these problems.

Believe it or not, it is not a very good idea to use a plunger if your toilet is clogged. Plungers just push whatever is stuck deeper into the drain. Instead, it is a better idea to use a closet auger. It will do a better job and is affordable.

If your sink is letting rusty water out and it will not drain, it is mostly likely because of the biological scum and grease that is built up in the pipes. You need to have your drains professionally cleaned, allowing maximum flow through your drains. Your drains must be open completely.

In the winter months, if you live somewhere where temperatures fall below freezing, leave your faucets on a little bit to let a thin stream of water through. This will help prevent the pipes from freezing, which could be a major problem for you and all the pipes in your home.

During the winter months, your water heater works the hardest. To keep it in optimum condition, flush it out before winter arrives. Flushing the system helps remove the sediment buildup, which causes internal corrosion of your water heater, shortens its lifespan, and reduces heating efficiency. Connect a hose to the faucet near the bottom of the tank and drain several gallons by directing the water into a nearby drain.

On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.

Make sure that your tool box is ready for any project you are preparing to do. The last thing you want is to be knee deep in a job only to find that you are missing the one tool you need to finish. Be sure to have various sizes of pipe wrenches that can be used to complete any job.

When you are using your disposal you should always run cold water not hot water. You should run the cold water as long as the motor to the disposal is running. Always avoid overloading your disposal. Things like corn husks, onion skins, celery and other high fiber foods could clog your disposal.

As you can see, plumbing isn’t so scary when you know what to do. Follow the tips you’ve read here next time you have a problem with your plumbing, and soon your problem will be solved, all without having to call an expensive plumber to fix the problem for you.

Read More

Avoid Problems Painting Aluminum and Vinyl Siding

February 12, 2025   Matt

Avoid Problems Painting Aluminum and Vinyl Siding

Anyone with older aluminum siding is well aware of the paint chalking problem. Just rub your hand along the old siding and the chalky old paint will be all over your palm. Trying to get paint to stick to this could be a real problem. This is due to oxidation of the paint. Siding manufacturers originally referred to this problem as a “benefit”. They called it, “self cleaning”, as the paint literally washed off the house.
Older vinyl siding is also a problem. UV light fades vinyl siding over time and the siding becomes very unsightly.
Many unfortunate homeowners and contractors have experienced the dismay, when they repainted their homes, only to find the new paint peeling off a few months later. Both problems with older aluminum and vinyl siding can be overcome with proper cleaning, surface preparation and re-painting.
Cleaning
You will need to rent a powerful pressure washer with at least 3000 psi. You will want a pressure washer powerful enough to remove most of the old chalky paint off the aluminum siding or, to remove any dirt buildup on the old vinyl siding.
Start at the top course of siding and work your way down. You will need to keep the pressure wand fairly close to the siding surface to effectively remove the old paint. In some areas, you may find that the paint comes off to the bare metal. Be careful near windows, corners, soffits and doorways. The water under pressure, can be forced behind these areas causing damage. You can add TSP or other cleaning solutions to the reservoir for mildew, algae or other grime built up. If you do use a cleaning solution, be sure to completely rinse it off with your pressure washer. You should allow your home to dry for several days in dry, sunny weather before proceeding to the painting process.
If you are repainting vinyl siding or vinyl coated aluminum siding, you may need a surface de-glosser. This is a solvent type product used to remove any shine on the surface and to help your first coat to adhere better. You will have no trouble finding a good de-glosser at your local paint supply store.
Application
I like a commercial type airless sprayer. It will draw the paint directly out of your 5 gallon paint pails, through the hose and into your spray gun. These are available to rent at many tool rental locations and even some paint supply stores that supply contractors. If your paint is real high quality latex, it will be thicker than regular latex paint and will require a more powerful airless sprayer.
Priming
This step is equally as critical as the step above. Actually, the cleaning and surface preparation phases will make or break the results of your project.
I like a latex paint additive called emulsa-bond for the first coat. Emulsa-bond is a bonding agent you will add to the first coat of paint or primer, to help it to bond to the old siding.
I buy the best grade exterior latex paint, rather than oil or other solvent based paint. Latex paint seems to keep up with the expansion and contraction of the siding very well. The high quality latex paint I buy needs no primer. I add the bonding agent directly into the first color coat. Check with your paint supplier whether or not to use a primer. The rule of thumb is, when in doubt, use a primer. If you use a primer, add the bonding agent into it before applying. There are also bonding agents available for oil or other solvent based paints. One type is called penetrol. These are usually available at a painting contractor supply store.
Many contractors will spot prime areas, especially where bare metal is exposed. I don’t like spot priming because it can lead to an uneven looking top coat. When I put a primer coat on, I prime the entire home. This gives a uniform surface finish later on.
Finish Coat
Your top coat will be color only. You should check with your paint manufacturer to see if you need one or two top coats after the base coat. Like I mentioned above, buy the highest quality exterior paint.
In Conclusion
Proper cleaning and surface preparation are the two main ingredients to a successful painting job. A bonding agent in the first coat is also very critical to avoid paint peeling off later on. Using these techniques, I’ve re-painted homes that have lasted far longer than the original factory applied finish.
ARTICLE REPRINT PERMISSION
You may reprint the above article in your electronic or print newsletter; however, please include my byline and bio and keep the article intact. I retain all copyrights.

Read More

Hot Tips To Fix Tough Plumbing Problems (5)

January 30, 2025   Matt

Hot Tips To Fix Tough Plumbing Problems

Anytime you have a plumbing problem, you do not need to get stressed out. This article will give you some tips to learn how to handle plumbing problems. Remember to take your time when fixing anything yourself so that you do not cause any further damage from happening to your pipes.

To conserve hot water each day, run your dishwasher late at night. This will help to maintain an adequate water level for your guests and for your chores in the morning or afternoon. Also, you can increase the supply of water available to you for cooking meals throughout the day.

Keep water trickling slightly from faucets to help prevent frozen pipes when the temperature drops significantly. Colder than normal temperatures can cause problems if pipes are not insulated appropriately, even when pipes are not exposed to the elements. By leaving the water running slightly, you keep movement in the pipes which can prevent freezing.

NEVER dump grease or oil down your drains! They both turn solid when they’re cold and can clog up your drains, especially in the kitchen and bathroom where other items end up going down the sink and creating blocks. Let it cool, instead, and throw it out in the trash.

When your toilet clogs and a plunger will not release it, try a closet auger. This tool features a handle that you rotate in order to feed a line into the toilet drain. When you remove the auger from the drain, the clog should come with it, unless it’s past the length to which the auger can reach.

Teach kids how to shut off the toilet’s water supply. Kids are notorious for putting large wads of toilet paper and other things into the toilet, which inevitably leads to the toilet overflowing. Especially if your bathroom has carpet, show kids how to turn the water valve off if the toilet water keeps rising, to prevent the mess of an overflow.

Keep an eye on your monthly water bill to catch plumbing problems. Has your water bill gone up recently, even though nothing’s changed? This could indicate a water leak or appliance problem somewhere inside or outside of your home. Check under sinks for rusted pipes, look for water puddles under outside faucets, and consider having a plumber come out to listen to your pipes to detect running water.

If you cannot turn off your main water valve before leaving on vacation, turn off the individual valves for the toilets, sinks, and washing machine. If the valves do not look like they are in good working order, then leave them on and that will be something that you need to have changed when you return.

You have learned many ways to handle a wide variety of plumbing problems. Take the advice in this article to use as a guide. If you have any further questions, make sure to take the time to find the answers using the internet or a professional so that you know exactly what you are doing before you start.

Read More

You Can Teach Yourself To Handle Plumbing Problems (2)

December 31, 2024   Matt

You Can Teach Yourself To Handle Plumbing Problems

Did you know that a leaky spray head on your kitchen sink might be caused by a faulty diverter? If this peaks your interest or if you want to know more about plumbing, then you will want to read what else we have to provide in this article about how to take care of plumbing in your home.

Periodically check your pipes for leaks and cracks. These can be forgotten, since pipes are usually hidden away, but checking for leaks and cracks can help you identify a small problem before a big problem occurs. You may have to enlist the help of a family member to turn on and off the water stream as you are checking.

Plunging is not the only way to unclog a troublesome toilet. If the water in the basin is sitting low and you know there’s a clog, try dropping hot water directly into the basin with a little bit of elevation, to apply enough force to help move along the clog.

Teach kids how to shut off the toilet’s water supply. Kids are notorious for putting large wads of toilet paper and other things into the toilet, which inevitably leads to the toilet overflowing. Especially if your bathroom has carpet, show kids how to turn the water valve off if the toilet water keeps rising, to prevent the mess of an overflow.

If water backs up from one sink to another, it is because the lines are connected. The part of the branch line for one device might be higher than another, but most likely there is also a blockage in the branch line connecting the two devices as well. This blockage must be cleaned.

If you ever put food down the garbage disposer after a meal, make sure that you run cold water for about 15 seconds to help drain the excess debris. This will help in flushing out the excess particles down your drain, which otherwise, can build up and cause a clog, eventually.

Avoid using hard cleaners on your toilets, such as drop-in cleaner tabs in the tank. When these tabs are almost completely dissolved, what’s left of the tab gets washed into the bowl. This can then end up clogging the toilet’s port holes, preventing the toilet from flushing properly. It can take months for this debris to finish dissolving in those holes.

A great plumbing tip which can save you a lot of money on a daily basis is to invest in a low GPF (gallons per flush) model toilet. As such, every time you flush the toilet you will be using less water than before, and doing so will save you on your water bill.

In conclusion, that leaky faucet may just be easier to fix than you imagined. Instead of making a call to a plumber, having to wait, and then paying out top dollar, you can now fix it yourself. Use this advice to put yourself in the best financial situation possible when it comes to plumbing.

Read More

Manage Your Plumbing Problems With These Tips (3)

December 26, 2024   Matt

Manage Your Plumbing Problems With These Tips

This is the best place for plumbing tips. You could look far and wide but you will not find tips as well written and clear as what you will find here. Use this article today if you want to know all that you should know about plumbing and your home.

Use strainers in all drains to catch hair and other objects. This will prevent all the material from going down the drain and causing a clog, which can cause a bigger problem down the line. Clean out the strainers daily so that you don’t start getting backup of water in your sink or tub.

If you find some moisture in the cabinet under your sink, but have determined for certain that there is not a faucet leak, do not just figure that it’s not a big deal. Other connections, such as your ice maker and dish washer, may also be located back under your sink. Take the time to see if one of these connections is the culprit.

If you can’t get a tight joint when installing new pipes, it’s probably because you didn’t cut it cleanly. Buy the right tools for the job like a pro-level tubing cutter, saw blades, and a pipe saw for plastic pipes. This will ensure that your cuts are clean and perfectly measured.

A great plumbing tip which can save you a lot of money on a daily basis is to invest in a low GPF (gallons per flush) model toilet. As such, every time you flush the toilet you will be using less water than before, and doing so will save you on your water bill.

If you have an underground leak in your pipes, it is possible to detect the leak before digging. Today’s leak detection equipment is very sophisticated and modern, allowing technicians to detect and pinpoint exactly where leaks are before they go about trying to fix them with professional grade equipment for you.

Did you know that it is suggested that you replace your water heater at least every 15 years? If your water heater has a rusting tank, it is just a matter of time before it breaks and floods the surrounding area with water. You can check the age of your water heater by observing its serial number. The first four numbers of the serial number on the water heater are the month and year it was manufactured.

Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.

In conclusion, plumbing is a skill that you should know about – plain and simple. It is something that you will always be able to use and you may be able to save yourself a lot of money and frustration in the future. Hopefully this article was beneficial to you.

Read More
« Older posts

  • Subscribe

Support us!

If you like this site please subscribe