Category Archives: Home Improvement

Fixing Leaky Faucets And Other Minor Plumbing Issues Yourself.

December 07, 2021   Matt

Fixing Leaky Faucets And Other Minor Plumbing Issues Yourself.

You will not find a greater collection of tips about plumbing anywhere else but here. Read this article if you need to know the best advice anywhere when it comes to plumbing and your house. You will thank yourself that you took the time to do so if any issues ever do occur at your house.

In order to keep your shower and bath tub drains in proper working order, try pouring a potful of boiling water into the drain at least every other week. Using this approach will clear out the constant hair and soapscum build-up that may occur even if you have installed a drain screen.

Avoid the bursting of pipes due to the change in the temperature. You need to allow the flow of heat to reach under the sinks and into the pipes, you have to keep the cabinet doors of the bathrooms and kitchens open. It is important to keep water running at both hot and cold faucets along with vanities that are in close proximity to exterior walls.

Before starting any plumbing project be sure to turn off the main water supply. Water damage can be one of the most expensive things to repair. To minimize damage turn the main water supply off as well as any shut off valves near where you are working. This will save a great deal of hardship later on.

It’s important to know how to turn off the water in your home in case the worst happens. For example, if your bathroom sink started leaking, do you know how to stop it? Walk around your home and find all the shut-off valves for each set of pipes and write them down. Create a map so you can always have a reference if necessary.

Do not use the liquid cleaning supplies that are designed to clear clogs. These cleaners are harmful and can damage your pipes as they clear the clog. Instead of using damaging liquids, use a plunger or a plumbing snake. These are much more effective and will not harm pipes.

Always keep a trash bin in the bathroom so that you can dispose of cotton swabs, facial pads, and hair. Do not put these materials in the toilet as they can cause clogs over time and disrupt your water flow. These items will not dissolve or break down when submerged in water.

You don’t need to add anything to a correctly installed septic system to ensure it’s working properly! In fact, chemicals being dumped down the drain can cause more problems by killing off the good bacteria needed to digest the waste. The best treatment for your system is to have it pumped at regular intervals.

In conclusion, you could look far and long but will not find a greater collection of advice regarding plumbing other than what you were just exposed to. Use this information and pass it on to those that you know in order to remove any risks that faulty plumbing might cause.

Read More

The Pros And Cons Of Doing Your Own Plumbing

December 02, 2021   Matt

The Pros And Cons Of Doing Your Own Plumbing

Simple plumbing issues can not only hurt the image of your home but they can destroy your wallet. Simple things from clogged drains, to more advanced leaks can be incredibly destructive. Don’t fret however! With a few essential tips for the do it yourself home plumber, you will be ready to take care of any issue.

A bad faucet might need new parts. If you need to change the cap, cut it on the side with a rotary tool. Cut the exterior part and the plastic seal, but make sure you stay clear of the brass inside of it. You can easily replace the exterior of the cap and the seal.

Your water heater works more during the fall and winter so make sure that you eliminate all sediment buildup around this piece of equipment. Flushing this device can lead to increased longevity so that you do not face plumbing problems during the winter. This precaution will save time, money and effort.

If you are having any kind of problems with your water line or plumbing in general then you will first want to cut of your water supply. One of the most common mistakes that people make is to leave their water running while they are trying to fix things and this leads to bigger problems.

If you’re connecting a new gas appliance in your home you absolutely need to have the right connector to add it to your gas plumbing. Universal connection kits are readily available at home improvement stores which will make the connection between your flexible hose and the iron supply pipe tight and safe.

Always keep a trash bin in the bathroom so that you can dispose of cotton swabs, facial pads, and hair. Do not put these materials in the toilet as they can cause clogs over time and disrupt your water flow. These items will not dissolve or break down when submerged in water.

If you have a foul odor coming from your garbage disposal, this is due to food debris buildup. You need to put ice cubes, orange peels, and lemon peels into the disposal and run for about 30 seconds. Next, run some liquid dish soap through the disposal. This should take care of the problem if there is not a substantial blocking buildup.

If your water bill seems unusually high and you haven’t changed your water usage, the problem is most likely in the service line. The cost to hire a professional to find and repair the service line most often is far greater than installing a new line and then having the old one shut off permanently.

Plumbing can be an advanced, highly technical profession where more often than not, you need an experts help. However, sometimes that is not the case and there are some simple do it yourself home fixes. If you take a little time to read about them you will find some of the most common plumbing problems are able to be handled by the common man.

Read More

Plumbing Problems Getting You Down? Read This! 2

November 27, 2021   Matt

Plumbing Problems Getting You Down? Read This!

Professional plumbing is often a very expensive service, and usually the work that is done is something that any homeowner could solve fairly easily with the proper knowledge and tools. If you’d like to start learning to solve your own plumbing problems, read on to see what you can do.

There are many ways to unclog a drain. You can try plunging it at first. If that doesn’t work try using a chemical agent from the store. Before you go and spend money at the store though, if you have baking soda and some vinegar handy, you can mix those together and pour them in the drain and try to plunge that but if all else fails they have stronger remedies at your local hardware store.

Beware of black water in your toilet tank. Chances are, the color is caused from too much magnesium or iron in your water. Although this is usually harmless, it can be annoying for some people. If it is iron or magnesium in your water, the only way to fix it is by filtering the water.

If you have a water pressure or fill problem throughout the whole house, do not panic. It could be the simplest of solutions. Sometimes the city flushes their systems, breaking up debris and sending it to homes. This requires cleaning drains effectively and strainers in order to resolve the problem.

In the winter time to avoid your pipes freezing you should insulate them. If the pipes are going to be in a place that is exposed to severely cold weather, you should drain them if they aren’t being used. If the pipes are indoor you should open up the cupboards under the sink so more heat can get to them.

When winterizing your plumbing system be sure to release the water through pressure. Often times people only close the shut off valves. This does not prevent your pipes from freezing. You must make sure the water is pushed out of the pipes completely or the pipes could freeze and burst into the home.

Basic problems with toilets can be a quick fix for even the rawest amateur plumber and is worth attempting if you can take the time to research the problem. Seek out the necessary part or parts from your local hardware store and ask for support in how to properly install them.

To make sure your sump pump will run in an emergency, routinely test it by adding several buckets of water into the sump pit. The pump should turn on, remove the water and turn off with ease. Do this regularly, especially if your sump pump doesn’t run that often, to ensure it will work when needed most.

As you can see, plumbing isn’t as difficult as you may have believed. Many plumbing problems can be solved easily with things on hand, or with a few inexpensive parts. Next time you have a problem with your plumbing, try using the tips in this article to solve it yourself!

Read More

Things You Need To Know For Your Next Plumbing Project (2)

November 22, 2021   Matt

Things You Need To Know For Your Next Plumbing Project

If you are a first time homeowner or maybe someone who has just moved out of Mom and Dad’s humble abode, you may not know a lick about plumbing, but there are certain things that you should know. This article will discuss some of them, and you will be more knowledgeable after reading the tips below.

If attempting a plumbing repair yourself, be sure and have plenty of buckets on hand to catch spilling water. While you may have turned off the water supply, there is always some water left in the pipes and the larger the home and more extensive the plumbing system, the more water you may encounter.

If you need to drill holes in your walls or ceilings, start with a hole big enough to fit your hand through it. Take a picture of the inside with a camera or a cell phone. Make sure you activate the flash function and take several pictures in different directions.

In any DIY plumbing project, make sure that you always test the drains and the supply lines before you close up the walls. It is a lot easier to find and solve problems if you look for them while you are still in the process of actively doing the job.

Is your shower pressure weak due to clogging of the openings in your shower head? Here is a simple and cost-effective tip to take care of that problem. Pour a cup of vinegar into a plastic bag, place it over the shower head, and twist tie it into place so it can soak overnight. In the morning, remove the plastic bag and use an old toothbrush to scrub off the mineral deposits which are clogging the openings. This will help to restore water flow and increase shower pressure.

If you’re connecting a new gas appliance in your home you absolutely need to have the right connector to add it to your gas plumbing. Universal connection kits are readily available at home improvement stores which will make the connection between your flexible hose and the iron supply pipe tight and safe.

For the most effective plunger to use on a toilet, choose one with a flange that sticks out from the end and fits into the hole in the bottom of the bowl. These typically work better than the classic cup-style plungers, since they create a tighter seal in the drain.

Make sure to never leave any flammable liquids near your water heater. Certain liquids like gasoline, solvents, or adhesives are flammable, and if left too close to the water heater, can ignite. If you have to have these liquids in your basement, place it far away from your water heater.

Now that you have read these plumbing tips, you should feel a little more comfortable about looking after that scary hardware that lurks in some rooms of your home. Follow the advice above and you are sure to do the right things when tinkering around with any of the pipes.

Read More

Determining And Fixing Plumbing Noises In Your Home

November 17, 2021   Matt

Determining And Fixing Plumbing Noises In Your Home

To diagnose noisy plumbing, it is important to determine first whether the unwanted sounds occur on the system’s inlet side-in other words, when water is turned on-or on the drain side. Noises on the inlet side have varied causes: excessive water pressure, worn valve and faucet parts, improperly connected pumps or other appliances, incorrectly placed pipe fasteners, and plumbing runs containing too many tight bends or other restrictions. Noises on the drain side usually stem from poor location or, as with some inlet side noise, a layout containing tight bends.

Hissing

Hissing noise that occurs when a faucet is opened slightly generally signals excessive water pressure. Consult your local water company if you suspect this problem; it will be able to tell you the water pressure in your area and can install a pressurereducing valve on the incoming water supply pipe if necessary.

Thudding

Thudding noise, often accompanied by shuddering pipes, when a faucet or appliance valve is turned off is a condition called water hammer. The noise and vibration are caused by the reverberating wave of pressure in the water, which suddenly has no place to go. Sometimes opening a valve that discharges water quickly into a section of piping containing a restriction, elbow, or tee fitting can produce the same condition.

Water hammer can usually be cured by installing fittings called air chambers or shock absorbers in the plumbing to which the problem valves or faucets are connected. These devices allow the shock wave created by the halted flow of water to dissipate in the air they contain, which (unlike water) is compressible.

Older plumbing systems may have short vertical sections of capped pipe behind walls on faucet runs for the same purpose; these can eventually fill with water, reducing or destroying their effectiveness. The cure is to drain the water system completely by shutting off the main water supply valve and opening all faucets. Then open the main supply valve and close the faucets one at a time, starting with the faucet nearest the valve and ending with the one farthest away.

Chattering or Screeching

Intense chattering or screeching that occurs when a valve or faucet is turned on, and that usually disappears when the fitting is opened fully, signals loose or defective internal parts. The solution is to replace the valve or faucet with a new one.

Pumps and appliances such as washing machines and dishwashers can transfer motor noise to pipes if they are improperly connected. Link such items to plumbing with plastic or rubber hoses-never rigid pipe-to isolate them.

Other Inlet Side Noises

Creaking, squeaking, scratching, snapping, and tapping usually are caused by the expansion or contraction of pipes, generally copper ones supplying hot water. The sounds occur as the pipes slide against loose fasteners or strike nearby house framing. You can often pinpoint the location of the problem if the pipes are exposed; just follow the sound when the pipes are making noise. Most likely you will discover a loose pipe hanger or an area where pipes lie so close to floor joists or other framing pieces that they clatter against them. Attaching foam pipe insulation around the pipes at the point of contact should remedy the problem. Be sure straps and hangers are secure and provide adequate support. Where possible, pipe fasteners should be attached to massive structural elements such as foundation walls instead of to framing; doing so lessens the transmission of vibrations from plumbing to surfaces that can amplify and transfer them. If attaching fasteners to framing is unavoidable, wrap pipes with insulation or other resilient material where they contact fasteners, and sandwich the ends of new fasteners between rubber washers when installing them.

Correcting plumbing runs that suffer from flow-restricting tight or numerous bends is a last resort that should be undertaken only after consulting a skilled plumbing contractor. Unfortunately, this situation is fairly common in older houses that may not have been built with indoor plumbing or that have seen several remodels, especially by amateurs.

Drainpipe Noise

On the drain side of plumbing, the chief goals are to eliminate surfaces that can be struck by falling or rushing water and to insulate pipes to contain unavoidable sounds.

In new construction, bathtubs, shower stalls, toilets, and wallmounted sinks and basins should be set on or against resilient underlayments to reduce the transmission of sound through them. Water-saving toilets and faucets are less noisy than conventional models; install them instead of older types even if codes in your area still permit using older fixtures.

Drainpipes that do not run vertically to the basement or that branch into horizontal pipe runs supported at floor joists or other framing present particularly troublesome noise problems. Such pipes are large enough to radiate considerable vibration; they also carry significant amounts of water, which makes the situation worse. In new construction, specify cast-iron soil pipes (the large pipes that drain toilets) if you can afford them. Their massiveness contains much of the noise made by water passing through them. Also, avoid routing drainpipes in walls shared with bedrooms and rooms where people gather. Walls containing drainpipes should be soundproofed as was described earlier, using double panels of sound-insulating fiberboard and wallboard. Pipes themselves can be wrapped with special fiberglass insulation made for the purpose; such pipes have an impervious vinyl skin (sometimes containing lead). Results are not always satisfactory.

Read More

Solid Advice On Finding A Reliable Plumber

November 12, 2021   Matt

Solid Advice On Finding A Reliable Plumber

Nobody really wants to think about having a huge plumbing issue in their home that requires a plumber. That’s because it can get expensive and can ruin your floors and other items in your home, if it gets out of hand. Never fear because you can learn to do your own to prevent such problems by following these tips below.

If you think you understand what is wrong with your toilet, but aren’t sure, you should first do some more research on the internet. Most plumbing problems are fairly standard, and you should be able to read about the problem in great detail on several amateur plumber forums to make sure you understand the problem.

If water is backing up into multiple fixtures all over the house, it is no longer going to be effective for you to use chemicals or a small hand snake. This is evidence of a blockage in the main line, and you must contact a professional to take care of this problem for you.

Tub drains can get clogged by hair and debris easily, but may be hard to access. Make use of an afghan hook to reach in and snag clogging materials. These hooks are available at most craft stores. Use slow, measured movements to avoid breaking the hair as you are pulling it out.

If you’re planning on connecting galvanized steel to copper pipes you need to use a dielectric union to make sure that the steel doesn’t corrode. It is made of both steel and copper and will ensure that the union is tight, safe, and lasts as long as your house is standing.

Protect you plumbing pipes! If you live in an area which has cold winters and are leaving your home for an extended amount of time, protect your plumbing while you are gone! Shut off the main water valve! Drain the system of water by opening the faucets at the highest and lowest points of the house. Also, make sure that you have left some heat on in the house! Set the thermostat to at least 55 degrees Fahrenheit.

If you have hard water, check intake hoses for washing machines and ice makers often to prevent them from splitting open from buildup. Lime scale remover can be used to remove buildup, but replacing hoses is an economical method as well to take care of the issue. Change out hoses when you change the batteries in your smoke alarms to stop unexpected floods.

Be careful with putting household cleaners in your toilet. They can cause the toilet to malfunction. The debris that these cleaners leave can sit in your toilet’s pipes and harden, making them almost impossible to get rid of. If it does harden, it usually requires the help of a professional.

Plumbing can incredibly fickle and being left with a huge plumbing bill or water damage can be disappointing to say the least. Do yourself a favor and follow these tips to start fixing and installing your own plumbing.

Read More
« Older posts
Newer posts »

  • Subscribe

Support us!

If you like this site please subscribe